total_downloads: 0
moderation: "accepted"
_id: "2hY1ZUWOOgdlRQrpUIIm"
steps:
  - text: "There are two main types of polymers, polar and nonpolar. Nonpolar Materials usually don't need to be dried. Exposing nonpolar materials (HDPE/PP etc.) to water is like putting oil in water. Almost every other commercial polymer has some level of polarity and therefore can absorb a certain amount of moisture from the air. Many materials are dried only to optimize surface appearance, too much moisture can lead to cosmetic defects known as splay or silver streaking. Other polymers are damaged if they are processed with too much moisture. These materials chemically react with the moisture (hydrolysis), resulting in a reduction in material strength. Check out the material overview below."
    _animationKey: "unique1"
    title: "When and why to dry"
    images:
      - contentType: "image/jpeg"
        updated: "2021-01-08T18:47:54.923Z"
        size: 95483
        timeCreated: "2021-01-08T18:47:54.923Z"
        type: "image/jpeg"
        downloadUrl: "https://firebasestorage.googleapis.com/v0/b/onearmyworld.appspot.com/o/uploads%2Fhowtos%2F2hY1ZUWOOgdlRQrpUIIm%2FErste%20Tabelle_Zeichenfla%CC%88che%201.png?alt=media&token=f25130cc-6ecc-46e6-8b8a-0bdd7da8765e"
        fullPath: "uploads/howtos/2hY1ZUWOOgdlRQrpUIIm/Erste Tabelle_Zeichenfläche 1.png"
        name: "Erste Tabelle_Zeichenflache 1.png"
  - images:
      - contentType: "image/jpeg"
        size: 93739
        downloadUrl: "https://firebasestorage.googleapis.com/v0/b/onearmyworld.appspot.com/o/uploads%2Fhowtos%2F2hY1ZUWOOgdlRQrpUIIm%2FZweite%20Tabelle_Zeichenfla%CC%88che%201.png?alt=media&token=b262254b-0826-424d-953f-fab9221442af"
        updated: "2021-01-08T18:47:56.359Z"
        timeCreated: "2021-01-08T18:47:56.359Z"
        type: "image/jpeg"
        fullPath: "uploads/howtos/2hY1ZUWOOgdlRQrpUIIm/Zweite Tabelle_Zeichenfläche 1.png"
        name: "Zweite Tabelle_Zeichenflache 1.png"
    text: "There are several different DIY methods to dry polymeres; you can use an oven, a dehydrator or a vacuum dryer.\nBut In this How-To we will focus on a self-built drybox with silica gel, because this method delivers the best results while being cheap, easy and energy efficient. One of the problems we encountered with the oven is overheating the plastic, resulting in a big mess. We tried replacing the silica gel with a household dehydrator, but they are not designed to achieve this kind of low humidity levels needed to effectively dry plastic. We also included a temperature table for different polymers.\n"
    _animationKey: "unique2"
    title: "Different drying methods"
  - images:
      - fullPath: "uploads/howtos/2hY1ZUWOOgdlRQrpUIIm/Step 3 (2).jpg"
        size: 96602
        downloadUrl: "https://firebasestorage.googleapis.com/v0/b/onearmyworld.appspot.com/o/uploads%2Fhowtos%2F2hY1ZUWOOgdlRQrpUIIm%2FStep%203%20(2).jpg?alt=media&token=f437721b-95db-45c1-9526-5f42c77f3ee6"
        name: "Step 3 (2).jpg"
        contentType: "image/jpeg"
        updated: "2021-01-08T18:47:57.971Z"
        type: "image/jpeg"
        timeCreated: "2021-01-08T18:47:57.971Z"
      - type: "image/jpeg"
        name: "Step 3.jpg"
        size: 90432
        fullPath: "uploads/howtos/2hY1ZUWOOgdlRQrpUIIm/Step 3.jpg"
        timeCreated: "2021-01-08T18:47:57.983Z"
        updated: "2021-01-08T18:47:57.983Z"
        downloadUrl: "https://firebasestorage.googleapis.com/v0/b/onearmyworld.appspot.com/o/uploads%2Fhowtos%2F2hY1ZUWOOgdlRQrpUIIm%2FStep%203.jpg?alt=media&token=c4630e06-3625-4e6e-ac1c-8a2cbd31604a"
        contentType: "image/jpeg"
    _animationKey: "unique3"
    text: "To make our drybox, we simply use a plastic box that we upgrade with some window seals to make it airtight. Simply, glue them to the rim of the box."
    title: "Make and airtight plastic box"
  - title: "Get Silica Gel"
    _animationKey: "unique3nb6ds"
    images:
      - size: 114021
        downloadUrl: "https://firebasestorage.googleapis.com/v0/b/onearmyworld.appspot.com/o/uploads%2Fhowtos%2F2hY1ZUWOOgdlRQrpUIIm%2FStep%204%20.jpg?alt=media&token=b38813db-9c68-4b21-8293-d4cfbd3e2a08"
        fullPath: "uploads/howtos/2hY1ZUWOOgdlRQrpUIIm/Step 4 .jpg"
        contentType: "image/jpeg"
        type: "image/jpeg"
        updated: "2021-01-08T18:47:59.656Z"
        name: "Step 4 .jpg"
        timeCreated: "2021-01-08T18:47:59.656Z"
      - fullPath: "uploads/howtos/2hY1ZUWOOgdlRQrpUIIm/Step 4 (1).jpg"
        type: "image/jpeg"
        downloadUrl: "https://firebasestorage.googleapis.com/v0/b/onearmyworld.appspot.com/o/uploads%2Fhowtos%2F2hY1ZUWOOgdlRQrpUIIm%2FStep%204%20(1).jpg?alt=media&token=dffe0eb9-fa26-430f-8be5-b6cba9ffd477"
        size: 103027
        updated: "2021-01-08T18:47:59.677Z"
        contentType: "image/jpeg"
        name: "Step 4 (1).jpg"
        timeCreated: "2021-01-08T18:47:59.677Z"
    text: "You might already know silica gel from a shoebox for instance. It comes in small bags in order to keep the inside dry by absorbing any moisture. Silica gel works perfectly with polymers as well so just put around 2 kilograms in the plastic box. There is no particular amount you have to use, but the more you have in the box the less often you need to take them out and dry them.\n"
  - _animationKey: "uniquezql6vm"
    text: "A hygrometer comes in handy to check the humidity inside the drybox. It is convenient to use a transparent box so you can keep track of the drying process at all time.\n"
    images:
      - downloadUrl: "https://firebasestorage.googleapis.com/v0/b/onearmyworld.appspot.com/o/uploads%2Fhowtos%2F2hY1ZUWOOgdlRQrpUIIm%2FStep%205.jpg?alt=media&token=fac32d09-bf72-4ac8-8584-007bdd3aeb47"
        name: "Step 5.jpg"
        type: "image/jpeg"
        fullPath: "uploads/howtos/2hY1ZUWOOgdlRQrpUIIm/Step 5.jpg"
        updated: "2021-01-08T18:48:01.274Z"
        contentType: "image/jpeg"
        size: 115309
        timeCreated: "2021-01-08T18:48:01.274Z"
      - fullPath: "uploads/howtos/2hY1ZUWOOgdlRQrpUIIm/Step 5 (2).jpg"
        contentType: "image/jpeg"
        name: "Step 5 (2).jpg"
        updated: "2021-01-08T18:48:01.243Z"
        downloadUrl: "https://firebasestorage.googleapis.com/v0/b/onearmyworld.appspot.com/o/uploads%2Fhowtos%2F2hY1ZUWOOgdlRQrpUIIm%2FStep%205%20(2).jpg?alt=media&token=a4d33adf-a130-4b0d-9f91-53b6bd68f482"
        timeCreated: "2021-01-08T18:48:01.243Z"
        size: 95356
        type: "image/jpeg"
    title: "Get a hygrometer"
  - _animationKey: "unique1klu2m"
    images:
      - updated: "2021-01-08T18:48:02.918Z"
        type: "image/jpeg"
        fullPath: "uploads/howtos/2hY1ZUWOOgdlRQrpUIIm/Step 6.jpg"
        contentType: "image/jpeg"
        downloadUrl: "https://firebasestorage.googleapis.com/v0/b/onearmyworld.appspot.com/o/uploads%2Fhowtos%2F2hY1ZUWOOgdlRQrpUIIm%2FStep%206.jpg?alt=media&token=9826c8eb-645d-4d6b-a535-fee10fff4693"
        size: 124121
        timeCreated: "2021-01-08T18:48:02.918Z"
        name: "Step 6.jpg"
      - updated: "2021-01-08T18:48:02.880Z"
        contentType: "image/jpeg"
        fullPath: "uploads/howtos/2hY1ZUWOOgdlRQrpUIIm/Step 6 (2).jpg"
        timeCreated: "2021-01-08T18:48:02.880Z"
        downloadUrl: "https://firebasestorage.googleapis.com/v0/b/onearmyworld.appspot.com/o/uploads%2Fhowtos%2F2hY1ZUWOOgdlRQrpUIIm%2FStep%206%20(2).jpg?alt=media&token=2252ef8e-1f93-4bdd-9954-f2ec26c0d4ee"
        size: 121334
        type: "image/jpeg"
        name: "Step 6 (2).jpg"
    text: "Using a microplastic bag (we use one from Guppyfriend) to place the material inside of the drybox will save you time and space. It keeps everything in place while the humidity can get out.\n"
    title: "Place granulate inside the box"
  - _animationKey: "uniqueko7p1"
    text: "The simplest method to measure how much moisture has been absorbed is weighing the granulate beforehand and afterwards. \nUnfortunately, if you are using hot air to dry granulat, volatiles are released from the sample, also reducing the weight. Therefore the weight loss does not exactly equal the loss of moisture so the measurement is imprecise. The professional approach involves making accurate moisture measurements in the drying hopper. This is possible using measurements of dielectric properties in real time. sensors are very expensive though.\n"
    images:
      - type: "image/jpeg"
        fullPath: "uploads/howtos/2hY1ZUWOOgdlRQrpUIIm/Step 7.jpg"
        size: 128707
        downloadUrl: "https://firebasestorage.googleapis.com/v0/b/onearmyworld.appspot.com/o/uploads%2Fhowtos%2F2hY1ZUWOOgdlRQrpUIIm%2FStep%207.jpg?alt=media&token=4048db70-d401-44b2-862d-2159b6d1b7dc"
        timeCreated: "2021-01-08T18:48:04.160Z"
        contentType: "image/jpeg"
        updated: "2021-01-08T18:48:04.160Z"
        name: "Step 7.jpg"
    title: "Check the results"
  - _animationKey: "uniquezmow7q"
    text: "After a while, you will notice that the silica gel reaches its maximum capacity of water that it can absorb. Simply put it in the oven for one or two hours at about 100°C/212°F and it will be as good as new.\n"
    images:
      - size: 275739
        downloadUrl: "https://firebasestorage.googleapis.com/v0/b/onearmyworld.appspot.com/o/uploads%2Fhowtos%2F2hY1ZUWOOgdlRQrpUIIm%2FDef7hdBUwAA2YTq.jpg?alt=media&token=1708b3cb-0ff5-4950-aeb2-5f42fdebf62a"
        updated: "2021-01-08T18:48:05.835Z"
        name: "Def7hdBUwAA2YTq.jpg"
        contentType: "image/jpeg"
        fullPath: "uploads/howtos/2hY1ZUWOOgdlRQrpUIIm/Def7hdBUwAA2YTq.jpg"
        type: "image/jpeg"
        timeCreated: "2021-01-08T18:48:05.835Z"
    title: "Renew the silica gel"
  - text: "Rapid changes in the Temperature lead to surface moisture.\nIf a cold drink placed outside in the hot summer, you will notice that water starts condensing on the surface.\nThis also is the case for polymers. We had many problems because we took plastic from the cold, damp garage to the warm production area. This resulted in a lot of surface moisture that produced bubbles and inconsistencies in our 3D-Printing Filament.\n"
    title: "Bonus tip"
    _animationKey: "unique3hd523"
    images:
      - size: 134616
        type: "image/jpeg"
        timeCreated: "2021-01-08T18:48:06.937Z"
        downloadUrl: "https://firebasestorage.googleapis.com/v0/b/onearmyworld.appspot.com/o/uploads%2Fhowtos%2F2hY1ZUWOOgdlRQrpUIIm%2FStep%20last.jpg?alt=media&token=d4643b72-fcc7-4b47-98ea-39fbb2d626e2"
        name: "Step last.jpg"
        updated: "2021-01-08T18:48:06.937Z"
        contentType: "image/jpeg"
        fullPath: "uploads/howtos/2hY1ZUWOOgdlRQrpUIIm/Step last.jpg"
      - type: "image/jpeg"
        contentType: "image/jpeg"
        updated: "2021-01-08T18:48:06.921Z"
        name: "Step last 2.jpg"
        size: 81823
        timeCreated: "2021-01-08T18:48:06.921Z"
        fullPath: "uploads/howtos/2hY1ZUWOOgdlRQrpUIIm/Step last 2.jpg"
        downloadUrl: "https://firebasestorage.googleapis.com/v0/b/onearmyworld.appspot.com/o/uploads%2Fhowtos%2F2hY1ZUWOOgdlRQrpUIIm%2FStep%20last%202.jpg?alt=media&token=a57a70a5-55fc-499f-9999-eb21247bc0d0"
      - updated: "2021-01-08T18:48:06.980Z"
        size: 122617
        downloadUrl: "https://firebasestorage.googleapis.com/v0/b/onearmyworld.appspot.com/o/uploads%2Fhowtos%2F2hY1ZUWOOgdlRQrpUIIm%2FSte%20last%203.jpg?alt=media&token=e4b06aff-d7b9-4f47-89cc-1f9e33301bb5"
        fullPath: "uploads/howtos/2hY1ZUWOOgdlRQrpUIIm/Ste last 3.jpg"
        timeCreated: "2021-01-08T18:48:06.980Z"
        contentType: "image/jpeg"
        type: "image/jpeg"
        name: "Ste last 3.jpg"
_contentModifiedTimestamp: "2023-06-14T11:02:18.017Z"
_deleted: false
fileLink: ""
_modified: "2024-01-06T08:22:06.532Z"
description: "When you want to make products using more advanced Materials (e.g. industrial waste), drying your granulate is a necessary step. \nWe will show you how to dry your granulate before extrusion cheaply and effectively, which is especially important if you want to make high quality products like 3d printing filament.\n\nYou can check out our How-To video here:\nhttps://youtu.be/dkm_gXxX2pk"
category:
  _modified: "2022-09-18T08:51:47.196Z"
  label: "Guides"
  _id: "CrZjHORWfxEl6iDrrPIO"
  _created: "2022-09-18T08:51:47.196Z"
  _deleted: false
votedUsefulBy:
  - "wastedtreasure"
  - "mattia"
  - "sigolene"
  - "precious-plastic-genova"
  - "andrmines"
  - "guille-staufert"
  - "johannplasto"
  - "los-angeles-plastic"
  - "qitech-industries"
  - "scohlendorf"
  - "stan_dingwater"
  - "tudi"
tags:
  - "hack"
comments: []
_createdBy: "qitech-industries"
slug: "dry-materials-for-higher-quality-products"
_created: "2021-01-08T18:48:07.330Z"
title: "Dry materials for higher quality products"
id: "2hY1ZUWOOgdlRQrpUIIm"
cover_image:
  downloadUrl: "https://firebasestorage.googleapis.com/v0/b/onearmyworld.appspot.com/o/uploads%2Fhowtos%2F2hY1ZUWOOgdlRQrpUIIm%2FPrecious%20Plastic%20Thumbnail.jpg?alt=media&token=4e1460df-2c9c-4010-b706-23d61338499c"
  type: "image/jpeg"
  contentType: "image/jpeg"
  updated: "2021-01-08T18:47:53.393Z"
  name: "Precious Plastic Thumbnail.jpg"
  fullPath: "uploads/howtos/2hY1ZUWOOgdlRQrpUIIm/Precious Plastic Thumbnail.jpg"
  size: 221411
  timeCreated: "2021-01-08T18:47:53.393Z"
creatorCountry: "de"
total_views: 634
files: []
difficulty_level: "Easy"
time: "< 1 hour"
user:
  detail:
    shortDescription: "We build machines to make 3D-printing filament "
    verifiedBadge: true
    name: "qitech-industries"
    displayName: "QiTech Industries"
    heroImageUrl: "https://firebasestorage.googleapis.com/v0/b/onearmyworld.appspot.com/o/uploads%2Fusers%2FPIp5TJF8g3aYbMBtf6i4ewwVbf12%2FMilan%20%2B%20Simon%20in%20Haupthalle%20unten-01-1887b811b1c.jpg?alt=media&token=f90d2eec-28b8-4ea7-9d53-d09d0868c95c"
    country: "de"
    profilePicUrl: "https://firebasestorage.googleapis.com/v0/b/onearmyworld.appspot.com/o/avatars%2Fqitech-industries.jpg?alt=media"
    profileUrl: "https://community.preciousplastic.com/u/qitech-industries"
    lastActive: "2021-09-20T21:02:35.338Z"
  moderation: "accepted"
  type: "machine-builder"
  _id: "qitech-industries"
  _created: "2023-06-02T09:49:55.022Z"
  verified: false
  _modified: "2023-06-02T18:48:52.165Z"
  _deleted: false
  location:
    lng: 8.64128351211548
    lat: 49.879394800806594
  geo:
    latitude: 49.879394800806594
    lookupSource: "coordinates"
    longitude: 8.64128351211548
    localityLanguageRequested: "en"
    continent: "Europe"
    continentCode: "EU"
    countryName: "Germany"
    countryCode: "DE"
    principalSubdivision: "Hessen"
    principalSubdivisionCode: "DE-HE"
    city: "Darmstadt"
    locality: "Darmstadt-Nord"
    postcode: "64293"
    plusCode: "8FXCVJHR+QG"
    localityInfo:
      administrative:
        - name: "Germany"
          description: "country in central Europe"
          isoName: "Germany"
          order: 3
          adminLevel: 2
          isoCode: "DE"
          wikidataId: "Q183"
          geonameId: 2921044
        - name: "Hessen"
          description: "state in the center of Germany"
          isoName: "Hessen"
          order: 4
          adminLevel: 4
          isoCode: "DE-HE"
          wikidataId: "Q1199"
          geonameId: 2905330
        - name: "Darmstadt Government Region"
          description: "administrative subdivision and region of Hesse, Germany"
          order: 6
          adminLevel: 5
          wikidataId: "Q7932"
          geonameId: 2938912
        - name: "Darmstadt"
          description: "city in Hesse, Germany"
          order: 10
          adminLevel: 6
          wikidataId: "Q2973"
          geonameId: 2938913
        - name: "Darmstadt-Nord"
          description: "human settlement in Germany"
          order: 11
          adminLevel: 9
          wikidataId: "Q1166439"
      informative:
        - name: "Europe"
          description: "continent"
          isoName: "Europe"
          order: 1
          isoCode: "EU"
          wikidataId: "Q46"
          geonameId: 6255148
        - name: "Europe/Berlin"
          description: "time zone"
          order: 2
        - name: "Rhein-Main-Verkehrsverbund"
          order: 5
        - name: "Bergstrasse-Odenwald Geo-Nature Park"
          description: "nature park in Hesse, Baden-Württemberg and Bavaria, Germany"
          order: 7
          wikidataId: "Q883865"
        - name: "Transitional Area VAB->RMV"
          order: 8
        - name: "constituency for the Bundestag election Darmstadt"
          description: "federal electoral district of Germany"
          order: 9
          wikidataId: "Q1008074"
        - name: "64293"
          description: "postal code"
          order: 12
  data:
    urls:
      - name: "Website"
        url: "https://www.qitech.de/industries"
      - name: "Instagram"
        url: "https://www.instagram.com/qitech.industries/"
      - name: "Youtube"
        url: "https://www.youtube.com/channel/uc4lok6v1hhjct5t2ljaklca"
      - name: "Facebook"
        url: "https://www.facebook.com/qitech.industries"
      - name: "Email"
        url: "mailto:contact@qitech.de"
      - name: "sponsor the work"
        url: "https://www.patreon.com/one_army"
    description: "We are four students from Germany who are passionate about technology and 3D printing. As a team, our goal is to create freedom in 3D printing, material production and research by providing reliable recycling solutions."
    services:
      - welding: false
        assembling: false
        machining: true
        electronics: true
        molds: false
    title: "QiTech Industries"
    images: []
images: []