--- title: Design an injection mould slug: design-an-injection-mould description: # Design Guide for a Broom Hanger Mold This guide outlines the steps to design a mold for an injection machine. tags: ["injection","mould"] category: Guides difficulty: Medium time: < 1 week location: Bogota, Colombia --- import { Image } from 'astro:assets' # Design an injection mould

# Design Guide for a Broom Hanger Mold This guide outlines the steps to design a mold for an injection machine. User Location: Bogota, Colombia ## Steps ### Step 1: Measure existing dimensions Ensure accuracy from the start. When designing a product to fit with an existing item, take precise measurements from it to establish a correct baseline. For this broom hanger, I measured broom and mop diameters, ranging from 0.83 to 0.94 inches (21-24 mm). I will use the smaller measurement of 0.83 inches (21 mm) as a reference for the clamping system design.

### Step 2: Sketch out your product idea ### How to Develop a Design Initiating a design begins with outlining your ideas on paper. Document all essential details to shape an effective design. Particular attention should be given to aspects such as wall thickness, which influences: - Required injection pressure - Product flexibility - Material resistance and durability To address these aspects, examine and compare materials from previously developed products.

### Step 3: “Mold” your idea ### Mold Design for Product Shape The broom hanger will be created using an injection machine, necessitating an enclosed mold. With the previously sketched product concept, I proceed to design the mold, focusing on six key criteria: 1. **Define the Product Shape:** Ensure the mold accurately reflects the intended design. 2. **Use Standard Measures:** Adhere to typical size specifications. 3. **Facilitate Plastic Intake and Mold Connection:** Ensure efficient material flow and secure connection. 4. **Allow for Opening and Ejection Post-Injection:** Design for easy removal of the finished product. 5. **Enable Adjustment and Closure:** Ensure precise alignment and secure closing mechanisms. 6. **Simplify the Machining Process:** Design for ease of manufacturing and operation. Each criterion will be detailed in the subsequent steps.

### Step 4: Define the product shape Certainly, here is the revised text: --- Consider the shapes that will form the cavity inside the mold. For this product, there are three components: 1. A cylinder (part 1) for the broomstick space. 2. A concentric circular tube (part 2) for the exterior of the hanger. 3. A block (part 3) to form the inner space and create an opening. Next, select the standard bars or tubes to use.

### Step 5: Use standard measures ### Material Measurements for Makers In Colombia, materials such as metal bars and steel planks are commonly available in inches, which often makes them more accessible and cost-effective. Adapting to these standard measurements can help you avoid unnecessary expenses. For the inner cylinder, consider using a ¾ inch (19.05 mm) rod, which closely matches the 21 mm broomstick size. For the outer wall, a 1 inch (25.4 mm) tube is recommended, resulting in an approximate broom hanger thickness of ⅛ inch (3.17 mm). Investigate your local market to identify the most suitable measurements for your project.

### Step 6: Plastic flow and mold connection Consider the flow of plastic within the mold. The path should be as short as possible with sufficient space for complete distribution. Drill a ¼ inch (6.35 mm) hole for entry, with a maximum height of 0.39 inches (10 mm), positioned centrally to ensure even distribution. For the broom hanger, fill the mold from its center. To connect the mold to the injection machine, use half of a standard ½ inch (12.7 mm) pipe nipple, welded to a flange that attaches to the mold with closing screws.

### Step 7: Open after injection and expluse the product As the plastic solidifies into the product, ensure the mold can be opened to release it. The mold should split into several parts for this purpose. However, fewer parts result in a simpler, more stable, and cost-effective mold. For the broom hanger, which functions as a hook, consider using three pieces: two for the exterior, which split in half to release the product, and one for the interior that will hold the broomstick and be removed by pulling it out.

### Step 8: Adjust and close ### Mold Assembly and Alignment To ensure proper alignment and withstand injection pressure, employ male/female guides between mold parts for a secure fit. Conic dowels are effective in maintaining alignment during assembly. For closure and pressure resistance, use through screws to tightly secure mold parts. Drill mold holes slightly larger than the screws (for 1/4-inch screws, drill 5/16-inch holes) to facilitate easier disassembly if parts shift during injection. Additionally, consider opening the screw hole side to allow screw removal by slightly loosening the bolts, avoiding the need for full removal.

### Step 9: Simplify the machining process Design your products using basic shapes such as cubes, cylinders, cones, and straight lines. These shapes are straightforward to create with manual lathes and mills. Utilizing concentric, aligned, and perpendicular figures enhances the machining process. Simplicity in design leads to simplicity in execution. Use standard measurements; for example, holes matching a drill bit's size and grooves matching a milling cutter's width allow for faster, more precise work. For instance, a broom hanger can be designed as a straight plastic tube with an opening on one side, involving straightforward line milling and circular hole creation for the mold parts. howto-broomhanger-mould-9..jpg

### Step 10: Use the PC tools We aim for greater precision than paper allows, so we utilize CAD software to model mold dimensions accurately. Continuing from the previous step, CAD enables us to create and refine mold versions based on the six design criteria. Here are some decisions made during the mold design process: - The injection point should be centrally located on the product's body. - To prevent pressure from opening the mold, the injection point should be on a solid section, not at the mold's seam. - The flange with the nipple connector should be affixed to a flat mold face using the same closing screws.

### Step 11: Document it The design process should culminate in detailed drawings and a comprehensive parts list. Consider the machining steps to identify critical procedures, such as machining parts together for precise fitting and determining fixation methods to the machine. Document all this information in the drawings. Create a parts list for all raw materials as a shopping guide. Include dimensions and quantities. Purchase raw parts slightly longer (0.2 to 0.4 inches) than final dimensions to accommodate machine fixation and final adjustments.

### Step 12: Turn it into reality With your mold design ready, proceed to construct it and create your product. Follow the instructions in the "Make a Broom Hanger" guide, or use these tips to develop an original idea.