---
title: Create a Perforated Board
slug: create-a-perforated-board
description: This method employs a heat press machine and an aluminum mold to create a plastic board, which is subsequently shaped into a perforated board.
tags: ["PP","sheetpress","mould"]
category: Products
difficulty: Medium
time: < 1 day
location: Tokyo, Japan
---
import { Image } from 'astro:assets'
# Create a Perforated Board
<Image src={import('./pegboard-1839e6fcddf.png')} alt="Create a Perforated Board" />
This method employs a heat press machine and an aluminum mold to create a plastic board, which is subsequently shaped into a perforated board.

User Location: Tokyo, Japan
## Steps
### Step 1: Prepare heat press machine and aluminum frame

### Materials
- **Heat Press Machine:** A commercially available heat press machine for iron-on printing with a 350x350 mm (13.78x13.78 in) heat surface.
- **Aluminum Frame:** Ordered from an online supplier, the frame is 230x300x4 mm (9.06x11.81x0.16 in) with a 5 mm (0.2 in) corner radius. It is sandwiched between two 2 mm (0.08 in) aluminum sheets and pressed.

### Reference
- Steps 1 and 2 are adapted from "Zero Plastic Australia's Sheet Machine" guide.


<Image src={import('./PXL_20220813_032907931-1839e74b577.jpg')} alt="PXL_20220813_032907931-1839e74b577.jpg" />


<Image src={import('./IMG_0367_1-1839e758749.PNG')} alt="IMG_0367 (1)-1839e758749.PNG" />

### Step 2: Create a plastic sheet

Aluminum sheet - Teflon sheet - Milled plastic & aluminum frame - Teflon sheet - Aluminum sheet

Arrange the materials in a heat press in the specified order. Apply silicone spray thoroughly to the aluminum frame. Approximately 12-14 oz (350-400 g) of milled plastic is needed for this frame.

Close the heat press and set it to 356°F (180°C) for 30-40 minutes. Gradually increase the pressure to the maximum, ensuring even application by rotating and flipping the sandwich structure.

After heating, turn off the press, keeping the pressure applied as the plastic cools and solidifies. Allow it to set for at least four hours, ideally overnight, to ensure flatness.

Once cool and solidified, remove the plastic sheet from the frame. Trim any excess with scissors, and the sheet is ready for use.


<Image src={import('./PXL_20220730_100113628-1839e75fa4f.jpg')} alt="PXL_20220730_100113628-1839e75fa4f.jpg" />


<Image src={import('./PXL_20220907_104904356.PORTRAIT-1839e762d36.jpg')} alt="PXL_20220907_104904356.PORTRAIT-1839e762d36.jpg" />

### Step 3: Drill Holes

Prepare a pegboard for guides. I used a pegboard measuring 11.8 x 7.9 inches (30 x 20 cm) with 5 mm holes spaced 25 mm apart.

Stack the pegboard on the plastic board and secure them with clamps. Drill 0.08-inch (2 mm) guide holes centered on the perforations.

Once the guide holes are complete, remove the pegboard. Secure the plastic board to the workbench and use a 0.2-inch (5 mm) drill bit to create the final holes based on the guides.


<Image src={import('./PXL_20220826_132812600-1839e7461fa.jpg')} alt="PXL_20220826_132812600-1839e7461fa.jpg" />


<Image src={import('./PXL_20220826_134239060-1839e747d11.jpg')} alt="PXL_20220826_134239060-1839e747d11.jpg" />

### Step 4: Finish with Sanding

After drilling all holes, remove any remaining plastic debris. Smooth the surface with an orbit sander. Sand up to about #2000 grit to achieve a bright color. 

The plastic pegboard is now complete.

For questions, please contact pebbles.recycleplastic@gmail.com.


<Image src={import('./PXL_20220911_133119936.PORTRAIT_1-1839e739c87.jpg')} alt="PXL_20220911_133119936.PORTRAIT (1)-1839e739c87.jpg" />