/** * Marlin 3D Printer Firmware * Copyright (c) 2020 MarlinFirmware [https://github.com/MarlinFirmware/Marlin] * * Based on Sprinter and grbl. * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm * * This program is free software: you can redistribute it and/or modify * it under the terms of the GNU General Public License as published by * the Free Software Foundation, either version 3 of the License, or * (at your option) any later version. * * This program is distributed in the hope that it will be useful, * but WITHOUT ANY WARRANTY; without even the implied warranty of * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the * GNU General Public License for more details. * * You should have received a copy of the GNU General Public License * along with this program. If not, see . * */ #pragma once #if !defined(__STM32F1__) && !defined(__STM32F4__) #error "Oops! Select an STM32F1/4 board in 'Tools > Board.'" #endif /** * 21017 Victor Perez Marlin for stm32f1 test */ #define BOARD_INFO_NAME "Beast STM32" #define DEFAULT_MACHINE_NAME "STM32F103RET6" // Enable I2C_EEPROM for testing #define I2C_EEPROM // Ignore temp readings during development. //#define BOGUS_TEMPERATURE_GRACE_PERIOD 2000 // // Steppers // #define X_STEP_PIN PE0 #define X_DIR_PIN PE1 #define X_ENABLE_PIN PC0 #define X_MIN_PIN PD5 #define X_MAX_PIN -1 #define Y_STEP_PIN PE2 #define Y_DIR_PIN PE3 #define Y_ENABLE_PIN PC1 #define Y_MIN_PIN PD6 #define Y_MAX_PIN #define Z_STEP_PIN PE4 #define Z_DIR_PIN PE5 #define Z_ENABLE_PIN PC2 #define Z_MIN_PIN PD7 #define Z_MAX_PIN -1 #define Y2_STEP_PIN -1 #define Y2_DIR_PIN -1 #define Y2_ENABLE_PIN -1 #define Z2_STEP_PIN -1 #define Z2_DIR_PIN -1 #define Z2_ENABLE_PIN -1 #define E0_STEP_PIN PE6 #define E0_DIR_PIN PE7 #define E0_ENABLE_PIN PC3 /** * TODO: Currently using same Enable pin to all steppers. */ #define E1_STEP_PIN PE8 #define E1_DIR_PIN PE9 #define E1_ENABLE_PIN PC4 #define E2_STEP_PIN PE10 #define E2_DIR_PIN PE11 #define E2_ENABLE_PIN PC5 // // Misc. Functions // #define SDSS PA15 #define LED_PIN PB2 #define PS_ON_PIN -1 #define KILL_PIN -1 // // Heaters / Fans // #define HEATER_0_PIN PD12 // EXTRUDER 1 #define HEATER_1_PIN PD13 #define HEATER_2_PIN PD14 #define HEATER_BED_PIN PB9 // BED #define HEATER_BED2_PIN -1 // BED2 #define HEATER_BED3_PIN -1 // BED3 #ifndef FAN_PIN #define FAN_PIN PB10 #endif #define FAN_SOFT_PWM // // Temperature Sensors // #define TEMP_BED_PIN PA0 // Analog Input #define TEMP_0_PIN PA1 // Analog Input #define TEMP_1_PIN PA2 // Analog Input #define TEMP_2_PIN PA3 // Analog Input // // LCD Pins // #if HAS_SPI_LCD #if ENABLED(REPRAPWORLD_GRAPHICAL_LCD) #define LCD_PINS_RS 49 // CS chip select /SS chip slave select #define LCD_PINS_ENABLE 51 // SID (MOSI) #define LCD_PINS_D4 52 // SCK (CLK) clock #elif BOTH(NEWPANEL, PANEL_ONE) #define LCD_PINS_RS PB8 #define LCD_PINS_ENABLE PD2 #define LCD_PINS_D4 PB12 #define LCD_PINS_D5 PB13 #define LCD_PINS_D6 PB14 #define LCD_PINS_D7 PB15 #else #define LCD_PINS_RS PB8 #define LCD_PINS_ENABLE PD2 #define LCD_PINS_D4 PB12 #define LCD_PINS_D5 PB13 #define LCD_PINS_D6 PB14 #define LCD_PINS_D7 PB15 #if DISABLED(NEWPANEL) #define BEEPER_PIN 33 // Buttons attached to a shift register // Not wired yet //#define SHIFT_CLK 38 //#define SHIFT_LD 42 //#define SHIFT_OUT 40 //#define SHIFT_EN 17 #endif #endif #if ENABLED(NEWPANEL) #if ENABLED(REPRAP_DISCOUNT_SMART_CONTROLLER) #define BEEPER_PIN 37 #define BTN_EN1 31 #define BTN_EN2 33 #define BTN_ENC 35 #define SD_DETECT_PIN 49 #define KILL_PIN 41 #if ENABLED(BQ_LCD_SMART_CONTROLLER) #define LCD_BACKLIGHT_PIN 39 #endif #elif ENABLED(REPRAPWORLD_GRAPHICAL_LCD) #define BTN_EN1 64 #define BTN_EN2 59 #define BTN_ENC 63 #define SD_DETECT_PIN 42 #elif ENABLED(LCD_I2C_PANELOLU2) #define BTN_EN1 47 #define BTN_EN2 43 #define BTN_ENC 32 #define LCD_SDSS 53 #define SD_DETECT_PIN -1 #define KILL_PIN 41 #elif ENABLED(LCD_I2C_VIKI) #define BTN_EN1 22 // http://files.panucatt.com/datasheets/viki_wiring_diagram.pdf explains 40/42. #define BTN_EN2 7 // 22/7 are unused on RAMPS_14. 22 is unused and 7 the SERVO0_PIN on RAMPS_13. #define BTN_ENC -1 #define LCD_SDSS 53 #define SD_DETECT_PIN 49 #elif ANY(VIKI2, miniVIKI) #define BEEPER_PIN 33 // Pins for DOGM SPI LCD Support #define DOGLCD_A0 44 #define DOGLCD_CS 45 #define LCD_SCREEN_ROT_180 #define BTN_EN1 22 #define BTN_EN2 7 #define BTN_ENC 39 #define SDSS 53 #define SD_DETECT_PIN -1 // Pin 49 for display sd interface, 72 for easy adapter board #define KILL_PIN 31 #define STAT_LED_RED_PIN 32 #define STAT_LED_BLUE_PIN 35 #elif ENABLED(ELB_FULL_GRAPHIC_CONTROLLER) #define BTN_EN1 35 #define BTN_EN2 37 #define BTN_ENC 31 #define SD_DETECT_PIN 49 #define LCD_SDSS 53 #define KILL_PIN 41 #define BEEPER_PIN 23 #define DOGLCD_CS 29 #define DOGLCD_A0 27 #define LCD_BACKLIGHT_PIN 33 #elif ENABLED(MINIPANEL) #define BEEPER_PIN 42 // Pins for DOGM SPI LCD Support #define DOGLCD_A0 44 #define DOGLCD_CS 66 #define LCD_BACKLIGHT_PIN 65 // backlight LED on A11/D65 #define SDSS 53 #define KILL_PIN 64 // GLCD features // Uncomment screen orientation //#define LCD_SCREEN_ROT_90 //#define LCD_SCREEN_ROT_180 //#define LCD_SCREEN_ROT_270 // The encoder and click button #define BTN_EN1 40 #define BTN_EN2 63 #define BTN_ENC 59 // not connected to a pin #define SD_DETECT_PIN 49 #else // Beeper on AUX-4 #define BEEPER_PIN 33 // Buttons directly attached to AUX-2 #if ENABLED(REPRAPWORLD_KEYPAD) #define BTN_EN1 64 #define BTN_EN2 59 #define BTN_ENC 63 #define SHIFT_OUT 40 #define SHIFT_CLK 44 #define SHIFT_LD 42 #elif ENABLED(PANEL_ONE) #define BTN_EN1 59 // AUX2 PIN 3 #define BTN_EN2 63 // AUX2 PIN 4 #define BTN_ENC 49 // AUX3 PIN 7 #else #define BTN_EN1 37 #define BTN_EN2 35 #define BTN_ENC 31 #endif #if ENABLED(G3D_PANEL) #define SD_DETECT_PIN 49 #define KILL_PIN 41 #else //#define SD_DETECT_PIN -1 // Ramps doesn't use this #endif #endif #endif // NEWPANEL #endif // HAS_SPI_LCD