/** * Marlin 3D Printer Firmware * Copyright (c) 2020 MarlinFirmware [https://github.com/MarlinFirmware/Marlin] * * Based on Sprinter and grbl. * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm * * This program is free software: you can redistribute it and/or modify * it under the terms of the GNU General Public License as published by * the Free Software Foundation, either version 3 of the License, or * (at your option) any later version. * * This program is distributed in the hope that it will be useful, * but WITHOUT ANY WARRANTY; without even the implied warranty of * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the * GNU General Public License for more details. * * You should have received a copy of the GNU General Public License * along with this program. If not, see . * */ #pragma once /** * RADDS */ #ifndef __SAM3X8E__ #error "Oops! Select 'Arduino Due' in 'Tools > Board.'" #endif #define BOARD_INFO_NAME "RADDS" // // Servos // #if !HAS_CUTTER #define SERVO0_PIN 5 #endif #define SERVO1_PIN 6 #define SERVO2_PIN 39 #define SERVO3_PIN 40 // // Limit Switches // #define X_MIN_PIN 28 #define X_MAX_PIN 34 #define Y_MIN_PIN 30 #define Y_MAX_PIN 36 #define Z_MIN_PIN 32 #define Z_MAX_PIN 38 // // Z Probe (when not Z_MIN_PIN) // #ifndef Z_MIN_PROBE_PIN #define Z_MIN_PROBE_PIN 38 #endif // // Steppers // #define X_STEP_PIN 24 #define X_DIR_PIN 23 #define X_ENABLE_PIN 26 #ifndef X_CS_PIN #define X_CS_PIN 25 #endif #define Y_STEP_PIN 17 #define Y_DIR_PIN 16 #define Y_ENABLE_PIN 22 #ifndef Y_CS_PIN #define Y_CS_PIN 27 #endif #define Z_STEP_PIN 2 #define Z_DIR_PIN 3 #define Z_ENABLE_PIN 15 #ifndef Z_CS_PIN #define Z_CS_PIN 29 #endif #define E0_STEP_PIN 61 #define E0_DIR_PIN 60 #define E0_ENABLE_PIN 62 #ifndef E0_CS_PIN #define E0_CS_PIN 31 #endif #define E1_STEP_PIN 64 #define E1_DIR_PIN 63 #define E1_ENABLE_PIN 65 #ifndef E1_CS_PIN #define E1_CS_PIN 33 #endif #define E2_STEP_PIN 51 #define E2_DIR_PIN 53 #define E2_ENABLE_PIN 49 #ifndef E2_CS_PIN #define E2_CS_PIN 35 #endif /** * RADDS Extension Board V2 / V3 * http://doku.radds.org/dokumentation/extension-board */ //#define RADDS_EXTENSION 2 #if RADDS_EXTENSION >= 2 #define E3_DIR_PIN 33 #define E3_STEP_PIN 35 #define E3_ENABLE_PIN 37 #ifndef E3_CS_PIN #define E3_CS_PIN 6 #endif #if RADDS_EXTENSION == 3 #define E4_DIR_PIN 27 #define E4_STEP_PIN 29 #define E4_ENABLE_PIN 31 #ifndef E4_CS_PIN #define E4_CS_PIN 39 #endif #define E5_DIR_PIN 66 #define E5_STEP_PIN 67 #define E5_ENABLE_PIN 68 #ifndef E5_CS_PIN #define E5_CS_PIN 6 #endif #define RADDS_EXT_MSI_PIN 69 #define BOARD_INIT() OUT_WRITE(RADDS_EXT_VDD_PIN, HIGH) #else #define E4_DIR_PIN 27 #define E4_STEP_PIN 29 #define E4_ENABLE_PIN 31 #ifndef E4_CS_PIN #define E4_CS_PIN 39 #endif // E3 and E4 share the same MSx pins #define E3_MS1_PIN 67 #define E4_MS1_PIN 67 #define E3_MS2_PIN 68 #define E4_MS2_PIN 68 #define E3_MS3_PIN 69 #define E4_MS3_PIN 69 #define RADDS_EXT_VDD2_PIN 66 #define BOARD_INIT() do{ OUT_WRITE(RADDS_EXT_VDD_PIN, HIGH); OUT_WRITE(RADDS_EXT_VDD2_PIN, HIGH); }while(0) #endif #define RADDS_EXT_VDD_PIN 25 #endif // // Temperature Sensors // #define TEMP_0_PIN 0 // Analog Input #define TEMP_1_PIN 1 // Analog Input #define TEMP_2_PIN 2 // Analog Input #define TEMP_3_PIN 3 // Analog Input #define TEMP_4_PIN 5 // dummy so will compile when PINS_DEBUGGING is enabled #define TEMP_BED_PIN 4 // Analog Input // SPI for Max6675 or Max31855 Thermocouple #if DISABLED(SDSUPPORT) #define MAX6675_SS_PIN 53 #else #define MAX6675_SS_PIN 49 #endif // // Heaters / Fans // #define HEATER_0_PIN 13 #define HEATER_1_PIN 12 #define HEATER_2_PIN 11 #if !HAS_CUTTER #define HEATER_BED_PIN 7 // BED #endif #ifndef FAN_PIN #define FAN_PIN 9 #endif #define FAN1_PIN 8 // // Misc. Functions // #define SD_DETECT_PIN 14 #define PS_ON_PIN 40 // SERVO3_PIN #ifndef FIL_RUNOUT_PIN #define FIL_RUNOUT_PIN 39 // SERVO2_PIN #endif #define I2C_EEPROM #define E2END 0x1FFF // 8KB // // M3/M4/M5 - Spindle/Laser Control // #if HAS_CUTTER #if !NUM_SERVOS #define SPINDLE_LASER_PWM_PIN 5 // SERVO0_PIN #endif #define SPINDLE_LASER_ENA_PIN 7 // HEATER_BED_PIN - Pullup/down! #endif // // LCD / Controller // #if HAS_SPI_LCD #if ENABLED(RADDS_DISPLAY) #define LCD_PINS_RS 42 #define LCD_PINS_ENABLE 43 #define LCD_PINS_D4 44 #define LCD_PINS_D5 45 #define LCD_PINS_D6 46 #define LCD_PINS_D7 47 #define BEEPER_PIN 41 #define BTN_EN1 50 #define BTN_EN2 52 #define BTN_ENC 48 #define BTN_BACK 71 #define SDSS 10 #define SD_DETECT_PIN 14 #elif ENABLED(REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER) // The REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER requires // an adapter such as https://www.thingiverse.com/thing:1740725 #define LCD_PINS_RS 42 #define LCD_PINS_ENABLE 43 #define LCD_PINS_D4 44 #define BEEPER_PIN 41 #define BTN_EN1 50 #define BTN_EN2 52 #define BTN_ENC 48 #define SDSS 10 #define SD_DETECT_PIN 14 #elif HAS_SSD1306_OLED_I2C #define BTN_EN1 50 #define BTN_EN2 52 #define BTN_ENC 48 #define BEEPER_PIN 41 #define LCD_SDSS 10 #define SD_DETECT_PIN 14 #elif ENABLED(SPARK_FULL_GRAPHICS) #define LCD_PINS_D4 29 #define LCD_PINS_ENABLE 27 #define LCD_PINS_RS 25 #define BTN_EN1 35 #define BTN_EN2 33 #define BTN_ENC 37 #endif // SPARK_FULL_GRAPHICS #endif // HAS_SPI_LCD #ifndef SDSS #define SDSS 4 #endif