/**
 * Marlin 3D Printer Firmware
 * Copyright (c) 2020 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
 *
 * Based on Sprinter and grbl.
 * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm
 *
 * This program is free software: you can redistribute it and/or modify
 * it under the terms of the GNU General Public License as published by
 * the Free Software Foundation, either version 3 of the License, or
 * (at your option) any later version.
 *
 * This program is distributed in the hope that it will be useful,
 * but WITHOUT ANY WARRANTY; without even the implied warranty of
 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
 * GNU General Public License for more details.
 *
 * You should have received a copy of the GNU General Public License
 * along with this program.  If not, see <http://www.gnu.org/licenses/>.
 *
 */

/**
 * CNControls V15 for HMS434 with DUE pin assignments
 */

#ifndef __SAM3X8E__
  #error "Oops! Select 'Arduino Due' in 'Tools > Board.'"
#endif

#define BOARD_INFO_NAME "CN Controls V15D"

//
// Servos
//
#define SERVO0_PIN                             6

//
// Limit Switches
//
#define X_STOP_PIN                            34
#define Y_STOP_PIN                            39
#define Z_STOP_PIN                            62

#ifndef Z_MIN_PROBE_PIN
  #define Z_MIN_PROBE_PIN                     49
#endif

//
// Steppers
//
#define X_STEP_PIN                            14
#define X_DIR_PIN                             25
#define X_ENABLE_PIN                          26

#define Y_STEP_PIN                            11
#define Y_DIR_PIN                             12
#define Y_ENABLE_PIN                          15

#define Z_STEP_PIN                            24
#define Z_DIR_PIN                             27
#define Z_ENABLE_PIN                          28

#define E0_STEP_PIN                           64
#define E0_DIR_PIN                            65
#define E0_ENABLE_PIN                         63

#define E1_STEP_PIN                            8
#define E1_DIR_PIN                             7
#define E1_ENABLE_PIN                         29

//
// Temperature Sensors
// Analog Inputs
//
#define TEMP_0_PIN                             1
#define TEMP_1_PIN                             2
#define TEMP_BED_PIN                           4

#ifndef TEMP_CHAMBER_PIN
  #define TEMP_CHAMBER_PIN                     5
#endif

//
// Heaters
//
#define HEATER_0_PIN                           3
#define HEATER_1_PIN                           4
#define HEATER_BED_PIN                        32
#define HEATER_CHAMBER_PIN                    33

//
// Fans
//
//#define FAN0_PIN                             8
#define ORIG_E0_AUTO_FAN_PIN                  30
#define ORIG_E1_AUTO_FAN_PIN                  30
#define ORIG_E2_AUTO_FAN_PIN                  30
#define ORIG_E3_AUTO_FAN_PIN                  30
#define ORIG_CHAMBER_AUTO_FAN_PIN             10

//
// SD card
//
#define SCK_PIN                               76
#define MISO_PIN                              74
#define MOSI_PIN                              75
#define SDSS                                  53
#define SD_DETECT_PIN                         40

// Common I/O

//#define PWM_1_PIN                            6  // probe
//#define PWM_2_PIN                           13
//#define SPARE_IO                            17
#define BEEPER_PIN                            13
#define STAT_LED_BLUE_PIN                     -1
#define STAT_LED_RED_PIN                      31

// G425 CALIBRATION_GCODE default pin
#ifndef CALIBRATION_PIN
  #define CALIBRATION_PIN                     66
#endif