/** * Marlin 3D Printer Firmware * Copyright (c) 2020 MarlinFirmware [https://github.com/MarlinFirmware/Marlin] * * Based on Sprinter and grbl. * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm * * This program is free software: you can redistribute it and/or modify * it under the terms of the GNU General Public License as published by * the Free Software Foundation, either version 3 of the License, or * (at your option) any later version. * * This program is distributed in the hope that it will be useful, * but WITHOUT ANY WARRANTY; without even the implied warranty of * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the * GNU General Public License for more details. * * You should have received a copy of the GNU General Public License * along with this program. If not, see . * */ #if !defined(__AVR_ATmega1280__) && !defined(__AVR_ATmega2560__) #error "Oops! Select 'Arduino/Genuino Mega or Mega 2560' in 'Tools > Board.'" #endif #if HOTENDS > 5 || E_STEPPERS > 5 #error "TTOSCAR supports up to 5 hotends / E-steppers. Comment out this line to continue." #endif #define BOARD_INFO_NAME "TT OSCAR" #define DEFAULT_MACHINE_NAME BOARD_INFO_NAME // // Servos // #define SERVO0_PIN 11 #define SERVO1_PIN 12 #define SERVO2_PIN 5 #define SERVO3_PIN 4 // // Limit Switches // #define X_MIN_PIN 3 #define X_MAX_PIN 2 #define Y_MIN_PIN 14 #define Y_MAX_PIN 15 #define Z_MIN_PIN 18 #define Z_MAX_PIN 19 // // Z Probe (when not Z_MIN_PIN) // #ifndef Z_MIN_PROBE_PIN #define Z_MIN_PROBE_PIN SERVO3_PIN #endif // // Steppers // #define X_STEP_PIN 54 #define X_DIR_PIN 55 #define X_ENABLE_PIN 38 #define X_CS_PIN 57 #define Y_STEP_PIN 60 #define Y_DIR_PIN 61 #define Y_ENABLE_PIN 56 #define Y_CS_PIN 58 #define Z_STEP_PIN 46 #define Z_DIR_PIN 48 #define Z_ENABLE_PIN 62 #define Z_CS_PIN 53 #define E0_STEP_PIN 26 #define E0_DIR_PIN 28 #define E0_ENABLE_PIN 24 #define E0_CS_PIN 49 #define E1_STEP_PIN 36 #define E1_DIR_PIN 34 #define E1_ENABLE_PIN 30 #define E1_CS_PIN E0_CS_PIN #define E2_STEP_PIN 63 #define E2_DIR_PIN 22 #define E2_ENABLE_PIN 59 #define E2_CS_PIN E0_CS_PIN #define E3_STEP_PIN 32 #define E3_DIR_PIN 40 #define E3_ENABLE_PIN 39 #define E3_CS_PIN E0_CS_PIN #define E4_STEP_PIN 43 #define E4_DIR_PIN 42 #define E4_ENABLE_PIN 47 #define E4_CS_PIN E0_CS_PIN #if HAS_TMC_UART /** * TMC2208/TMC2209 stepper drivers * * Hardware serial communication ports. * If undefined software serial is used according to the pins below */ //#define X_HARDWARE_SERIAL Serial1 //#define X2_HARDWARE_SERIAL Serial1 //#define Y_HARDWARE_SERIAL Serial1 //#define Y2_HARDWARE_SERIAL Serial1 //#define Z_HARDWARE_SERIAL Serial1 //#define Z2_HARDWARE_SERIAL Serial1 //#define E0_HARDWARE_SERIAL Serial1 //#define E1_HARDWARE_SERIAL Serial1 //#define E2_HARDWARE_SERIAL Serial1 //#define E3_HARDWARE_SERIAL Serial1 //#define E3_HARDWARE_SERIAL Serial1 // // Software serial // #define X_SERIAL_TX_PIN -1 // 59 #define X_SERIAL_RX_PIN -1 // 63 #define X2_SERIAL_TX_PIN -1 #define X2_SERIAL_RX_PIN -1 #define Y_SERIAL_TX_PIN -1 // 64 #define Y_SERIAL_RX_PIN -1 // 40 #define Y2_SERIAL_TX_PIN -1 #define Y2_SERIAL_RX_PIN -1 #define Z_SERIAL_TX_PIN -1 // 44 #define Z_SERIAL_RX_PIN -1 // 42 #define Z2_SERIAL_TX_PIN -1 #define Z2_SERIAL_RX_PIN -1 #define E0_SERIAL_TX_PIN -1 // 66 #define E0_SERIAL_RX_PIN -1 // 65 #define E1_SERIAL_TX_PIN -1 #define E1_SERIAL_RX_PIN -1 #define E2_SERIAL_TX_PIN -1 #define E2_SERIAL_RX_PIN -1 #define E3_SERIAL_TX_PIN -1 #define E3_SERIAL_RX_PIN -1 #define E4_SERIAL_TX_PIN -1 #define E4_SERIAL_RX_PIN -1 #define E5_SERIAL_RX_PIN -1 #define E6_SERIAL_RX_PIN -1 #define E7_SERIAL_RX_PIN -1 #endif // // Default pins for TMC software SPI // //#if ENABLED(TMC_USE_SW_SPI) // #ifndef TMC_SW_MOSI // #define TMC_SW_MOSI 66 // #endif // #ifndef TMC_SW_MISO // #define TMC_SW_MISO 44 // #endif // #ifndef TMC_SW_SCK // #define TMC_SW_SCK 64 // #endif //#endif // // Temperature Sensors // #define TEMP_0_PIN 13 #define TEMP_1_PIN 15 #define TEMP_2_PIN 10 #define TEMP_3_PIN 11 #define TEMP_BED_PIN 14 #if TEMP_SENSOR_CHAMBER > 0 #define TEMP_CHAMBER_PIN 12 #else #define TEMP_4_PIN 12 #endif // SPI for Max6675 or Max31855 Thermocouple //#if DISABLED(SDSUPPORT) // #define MAX6675_SS_PIN 66 // Don't use 53 if using Display/SD card //#else // #define MAX6675_SS_PIN 66 // Don't use 49 (SD_DETECT_PIN) //#endif // // Heaters / Fans // #define HEATER_0_PIN 10 #define HEATER_1_PIN 7 #define HEATER_2_PIN 44 #define HEATER_BED_PIN 8 #define FAN_PIN 9 #if EXTRUDERS >= 5 #define HEATER_4_PIN 6 #else #define FAN1_PIN 6 #endif #if EXTRUDERS >= 4 #define HEATER_3_PIN 45 #else #define FAN2_PIN 45 #endif // // Misc. Functions // #define SDSS 53 #define LED_PIN 13 //#ifndef FILWIDTH_PIN // #define FILWIDTH_PIN 5 // Analog Input //#endif // DIO 4 (Servos plug) for the runout sensor. //#define FIL_RUNOUT_PIN SERVO3_PIN #ifndef PS_ON_PIN #define PS_ON_PIN 12 #endif // // Case Light // #if ENABLED(CASE_LIGHT_ENABLE) && !PIN_EXISTS(CASE_LIGHT) && !defined(SPINDLE_LASER_ENABLE_PIN) #if !NUM_SERVOS // Prefer the servo connector #define CASE_LIGHT_PIN 6 // Hardware PWM #elif HAS_FREE_AUX2_PINS // Try to use AUX 2 #define CASE_LIGHT_PIN 44 // Hardware PWM #endif #endif // // M3/M4/M5 - Spindle/Laser Control // #if ENABLED(SPINDLE_LASER_ENABLE) && !PIN_EXISTS(SPINDLE_LASER_ENABLE) #if !NUM_SERVOS // Prefer the servo connector #define SPINDLE_LASER_ENABLE_PIN 4 // Pullup or pulldown! #define SPINDLE_LASER_PWM_PIN 6 // Hardware PWM #define SPINDLE_DIR_PIN 5 #elif HAS_FREE_AUX2_PINS // Try to use AUX 2 #define SPINDLE_LASER_ENABLE_PIN 40 // Pullup or pulldown! #define SPINDLE_LASER_PWM_PIN 44 // Hardware PWM #define SPINDLE_DIR_PIN 65 #endif #endif // // Průša i3 MK2 Multiplexer Support // //#ifndef E_MUX0_PIN // #define E_MUX0_PIN 58 // Y_CS_PIN //#endif //#ifndef E_MUX1_PIN // #define E_MUX1_PIN 53 // Z_CS_PIN //#endif //#ifndef E_MUX2_PIN // #define E_MUX2_PIN 49 // En_CS_PIN //#endif ////////////////////////// // LCDs and Controllers // ////////////////////////// #if HAS_SPI_LCD // // LCD Display output pins // #if ENABLED(REPRAPWORLD_GRAPHICAL_LCD) #define LCD_PINS_RS 49 // CS chip select /SS chip slave select #define LCD_PINS_ENABLE 51 // SID (MOSI) #define LCD_PINS_D4 52 // SCK (CLK) clock #elif BOTH(NEWPANEL, PANEL_ONE) #define LCD_PINS_RS 40 #define LCD_PINS_ENABLE 42 #define LCD_PINS_D4 65 #define LCD_PINS_D5 66 #define LCD_PINS_D6 44 #define LCD_PINS_D7 64 #elif ENABLED(ZONESTAR_LCD) #define LCD_PINS_RS 64 #define LCD_PINS_ENABLE 44 #define LCD_PINS_D4 63 #define LCD_PINS_D5 40 #define LCD_PINS_D6 42 #define LCD_PINS_D7 65 #define ADC_KEYPAD_PIN 12 #else #if ENABLED(CR10_STOCKDISPLAY) #define LCD_PINS_RS 27 #define LCD_PINS_ENABLE 29 #define LCD_PINS_D4 25 #if DISABLED(NEWPANEL) #define BEEPER_PIN 37 #endif #else #if EITHER(MKS_12864OLED, MKS_12864OLED_SSD1306) #define LCD_PINS_DC 25 // Set as output on init #define LCD_PINS_RS 27 // Pull low for 1s to init // DOGM SPI LCD Support #define DOGLCD_CS 16 #define DOGLCD_MOSI 17 #define DOGLCD_SCK 23 #define DOGLCD_A0 LCD_PINS_DC #else #define LCD_PINS_RS 16 #define LCD_PINS_ENABLE 17 #define LCD_PINS_D4 23 #define LCD_PINS_D5 25 #define LCD_PINS_D6 27 #endif #define LCD_PINS_D7 29 #if DISABLED(NEWPANEL) #define BEEPER_PIN 33 #endif #endif #if DISABLED(NEWPANEL) // Buttons attached to a shift register // Not wired yet //#define SHIFT_CLK 38 //#define SHIFT_LD 42 //#define SHIFT_OUT 40 //#define SHIFT_EN 17 #endif #endif // // LCD Display input pins // #if ENABLED(NEWPANEL) #if ENABLED(REPRAP_DISCOUNT_SMART_CONTROLLER) #define BEEPER_PIN 37 #if ENABLED(CR10_STOCKDISPLAY) #define BTN_EN1 17 #define BTN_EN2 23 #else #define BTN_EN1 31 #define BTN_EN2 33 #endif #define BTN_ENC 35 #define SD_DETECT_PIN 49 //#define KILL_PIN 41 #if ENABLED(BQ_LCD_SMART_CONTROLLER) #define LCD_BACKLIGHT_PIN 39 #endif #elif ENABLED(REPRAPWORLD_GRAPHICAL_LCD) #define BTN_EN1 64 #define BTN_EN2 59 #define BTN_ENC 63 #define SD_DETECT_PIN 42 #elif ENABLED(LCD_I2C_PANELOLU2) #define BTN_EN1 47 #define BTN_EN2 43 #define BTN_ENC 32 #define LCD_SDSS 53 //#define KILL_PIN 41 #elif ENABLED(LCD_I2C_VIKI) #define BTN_EN1 22 // http://files.panucatt.com/datasheets/viki_wiring_diagram.pdf explains 40/42. #define BTN_EN2 7 // 22/7 are unused on RAMPS_14. 22 is unused and 7 the SERVO0_PIN on RAMPS_13. #define BTN_ENC -1 #define LCD_SDSS 53 #define SD_DETECT_PIN 49 #elif EITHER(VIKI2, miniVIKI) #define DOGLCD_CS 45 #define DOGLCD_A0 44 #define LCD_SCREEN_ROT_180 #define BEEPER_PIN 33 #define STAT_LED_RED_PIN 32 #define STAT_LED_BLUE_PIN 35 #define BTN_EN1 22 #define BTN_EN2 7 #define BTN_ENC 39 #define SDSS 53 #define SD_DETECT_PIN -1 // Pin 49 for display SD interface, 72 for easy adapter board //#define KILL_PIN 31 #elif ENABLED(ELB_FULL_GRAPHIC_CONTROLLER) #define DOGLCD_CS 29 #define DOGLCD_A0 27 #define BEEPER_PIN 23 #define LCD_BACKLIGHT_PIN 33 #define BTN_EN1 35 #define BTN_EN2 37 #define BTN_ENC 31 #define LCD_SDSS 53 #define SD_DETECT_PIN 49 //#define KILL_PIN 41 #elif ENABLED(MKS_MINI_12864) #define DOGLCD_A0 27 #define DOGLCD_CS 25 // GLCD features //#define LCD_CONTRAST_INIT 190 // Uncomment screen orientation //#define LCD_SCREEN_ROT_90 //#define LCD_SCREEN_ROT_180 //#define LCD_SCREEN_ROT_270 #define BEEPER_PIN 37 #define LCD_BACKLIGHT_PIN 65 // backlight LED on A11/D65 #define BTN_EN1 31 #define BTN_EN2 33 #define BTN_ENC 35 //#define SDSS 53 #define SD_DETECT_PIN 49 //#define KILL_PIN 64 #elif ENABLED(MINIPANEL) #define BEEPER_PIN 42 // not connected to a pin #define LCD_BACKLIGHT_PIN 65 // backlight LED on A11/D65 #define DOGLCD_A0 44 #define DOGLCD_CS 66 // GLCD features //#define LCD_CONTRAST_INIT 190 // Uncomment screen orientation //#define LCD_SCREEN_ROT_90 //#define LCD_SCREEN_ROT_180 //#define LCD_SCREEN_ROT_270 #define BTN_EN1 40 #define BTN_EN2 63 #define BTN_ENC 59 #define SDSS 53 #define SD_DETECT_PIN 49 //#define KILL_PIN 64 #else // Beeper on AUX-4 #define BEEPER_PIN 33 // Buttons are directly attached to AUX-2 #if ENABLED(REPRAPWORLD_KEYPAD) #define SHIFT_OUT 40 #define SHIFT_CLK 44 #define SHIFT_LD 42 #define BTN_EN1 64 #define BTN_EN2 59 #define BTN_ENC 63 #elif ENABLED(PANEL_ONE) #define BTN_EN1 59 // AUX2 PIN 3 #define BTN_EN2 63 // AUX2 PIN 4 #define BTN_ENC 49 // AUX3 PIN 7 #else #define BTN_EN1 37 #define BTN_EN2 35 #define BTN_ENC 31 #endif #if ENABLED(G3D_PANEL) #define SD_DETECT_PIN 49 //#define KILL_PIN 41 #endif #endif #endif // NEWPANEL #endif