/**
 * Marlin 3D Printer Firmware
 * Copyright (c) 2020 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
 *
 * Based on Sprinter and grbl.
 * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm
 *
 * This program is free software: you can redistribute it and/or modify
 * it under the terms of the GNU General Public License as published by
 * the Free Software Foundation, either version 3 of the License, or
 * (at your option) any later version.
 *
 * This program is distributed in the hope that it will be useful,
 * but WITHOUT ANY WARRANTY; without even the implied warranty of
 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
 * GNU General Public License for more details.
 *
 * You should have received a copy of the GNU General Public License
 * along with this program.  If not, see <http://www.gnu.org/licenses/>.
 *
 */
#pragma once

/**
 * Formbot Raptor pin assignments
 */

#ifndef __AVR_ATmega2560__
  #error "Oops! Select 'Arduino/Genuino Mega or Mega 2560' in 'Tools > Board.'"
#elif HOTENDS > 3 || E_STEPPERS > 3
  #error "Formbot supports up to 3 hotends / E-steppers. Comment out this line to continue."
#endif

#ifndef BOARD_INFO_NAME
  #define BOARD_INFO_NAME      "Formbot Raptor"
#endif
#ifndef DEFAULT_MACHINE_NAME
  #define DEFAULT_MACHINE_NAME BOARD_INFO_NAME
#endif

//
// Servos
//
#define SERVO0_PIN                            11
#define SERVO1_PIN                             6
#define SERVO2_PIN                             5

//
// Limit Switches
//
#define X_MIN_PIN                              3
#ifndef X_MAX_PIN
  #define X_MAX_PIN                            2
#endif
#define Y_MIN_PIN                             14
#define Y_MAX_PIN                             15
#define Z_MIN_PIN                             18
#define Z_MAX_PIN                             19

//
// Z Probe (when not Z_MIN_PIN)
//
#ifndef Z_MIN_PROBE_PIN
  #define Z_MIN_PROBE_PIN                     32
#endif

//
// Steppers
//
#define X_STEP_PIN                            54
#define X_DIR_PIN                             55
#define X_ENABLE_PIN                          38
#ifndef X_CS_PIN
  #define X_CS_PIN                            53
#endif

#define Y_STEP_PIN                            60
#define Y_DIR_PIN                             61
#define Y_ENABLE_PIN                          56
#ifndef Y_CS_PIN
  #define Y_CS_PIN                            49
#endif

#define Z_STEP_PIN                            46
#define Z_DIR_PIN                             48
#define Z_ENABLE_PIN                          62
#ifndef Z_CS_PIN
  #define Z_CS_PIN                            40
#endif

#define E0_STEP_PIN                           26
#define E0_DIR_PIN                            28
#define E0_ENABLE_PIN                         24
#ifndef E0_CS_PIN
  #define E0_CS_PIN                           42
#endif

#define E1_STEP_PIN                           36
#define E1_DIR_PIN                            34
#define E1_ENABLE_PIN                         30
#ifndef E1_CS_PIN
  #define E1_CS_PIN                           44
#endif

#define E2_STEP_PIN                           42
#define E2_DIR_PIN                            43
#define E2_ENABLE_PIN                         44

//
// Temperature Sensors
//
#define TEMP_0_PIN                            13  // Analog Input
#define TEMP_1_PIN                            15  // Analog Input
#define TEMP_BED_PIN                          14  // Analog Input

// SPI for Max6675 or Max31855 Thermocouple
#if DISABLED(SDSUPPORT)
  #define MAX6675_SS_PIN                      66  // Don't use 53 if using Display/SD card
#else
  #define MAX6675_SS_PIN                      66  // Don't use 49 (SD_DETECT_PIN)
#endif

//
// Augmentation for auto-assigning RAMPS plugs
//
#if NONE(IS_RAMPS_EEB, IS_RAMPS_EEF, IS_RAMPS_EFB, IS_RAMPS_EFF, IS_RAMPS_SF) && !PIN_EXISTS(MOSFET_D)
  #if HOTENDS > 1
    #if TEMP_SENSOR_BED
      #define IS_RAMPS_EEB
    #else
      #define IS_RAMPS_EEF
    #endif
  #elif TEMP_SENSOR_BED
    #define IS_RAMPS_EFB
  #else
    #define IS_RAMPS_EFF
  #endif
#endif

//
// Heaters / Fans
//
#define HEATER_0_PIN                          10
#define HEATER_1_PIN                           7
#define HEATER_BED_PIN                         8

#ifndef FAN_PIN
  #define FAN_PIN                              9
#endif

#ifndef FIL_RUNOUT_PIN
  #define FIL_RUNOUT_PIN                      57
#endif

#if !HAS_FILAMENT_SENSOR
  #define FAN1_PIN                             4
#endif

//
// Misc. Functions
//
#ifndef SDSS
  #define SDSS                                53
#endif
#define LED_PIN                               13
#define LED4_PIN                               5

// Use the RAMPS 1.4 Analog input 5 on the AUX2 connector
#define FILWIDTH_PIN                           5  // Analog Input

#ifndef PS_ON_PIN
  #define PS_ON_PIN                           12
#endif

#define CASE_LIGHT_PIN                         5

//
// LCD / Controller
//
// Formbot only supports REPRAP_DISCOUNT_SMART_CONTROLLER
//
#if ENABLED(REPRAP_DISCOUNT_SMART_CONTROLLER)
  #define BEEPER_PIN                          37
  #define BTN_EN1                             31
  #define BTN_EN2                             33
  #define BTN_ENC                             35
  #define SD_DETECT_PIN                       49
  #define KILL_PIN                            41
  #define LCD_PINS_RS                         16
  #define LCD_PINS_ENABLE                     17
  #define LCD_PINS_D4                         23
  #define LCD_PINS_D5                         25
  #define LCD_PINS_D6                         27
  #define LCD_PINS_D7                         29
#endif