/**
 * Marlin 3D Printer Firmware
 * Copyright (c) 2020 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
 *
 * Based on Sprinter and grbl.
 * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm
 *
 * This program is free software: you can redistribute it and/or modify
 * it under the terms of the GNU General Public License as published by
 * the Free Software Foundation, either version 3 of the License, or
 * (at your option) any later version.
 *
 * This program is distributed in the hope that it will be useful,
 * but WITHOUT ANY WARRANTY; without even the implied warranty of
 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
 * GNU General Public License for more details.
 *
 * You should have received a copy of the GNU General Public License
 * along with this program.  If not, see <http://www.gnu.org/licenses/>.
 *
 */
#pragma once

/**
 * Smoothieboard pin assignments
 */

#ifndef MCU_LPC1769
  #error "Oops! Make sure you have the LPC1769 environment selected in your IDE."
#endif

#define BOARD_INFO_NAME   "Smoothieboard"
#define BOARD_WEBSITE_URL "smoothieware.org/smoothieboard"

//
// EEPROM
//
#define FLASH_EEPROM_EMULATION
//#define SDCARD_EEPROM_EMULATION

//
// Servos
//
#define SERVO0_PIN                         P1_23

//
// Limit Switches
//
#define X_MIN_PIN                          P1_24
#define X_MAX_PIN                          P1_25
#define Y_MIN_PIN                          P1_26
#define Y_MAX_PIN                          P1_27
#define Z_MIN_PIN                          P1_28
#define Z_MAX_PIN                          P1_29

//
// Steppers
//
#define X_STEP_PIN                         P2_00
#define X_DIR_PIN                          P0_05
#define X_ENABLE_PIN                       P0_04

#define Y_STEP_PIN                         P2_01
#define Y_DIR_PIN                          P0_11
#define Y_ENABLE_PIN                       P0_10

#define Z_STEP_PIN                         P2_02
#define Z_DIR_PIN                          P0_20
#define Z_ENABLE_PIN                       P0_19

#define E0_STEP_PIN                        P2_03
#define E0_DIR_PIN                         P0_22
#define E0_ENABLE_PIN                      P0_21

#define E1_STEP_PIN                        P2_08
#define E1_DIR_PIN                         P2_13
#define E1_ENABLE_PIN                      P4_29

//
// Temperature Sensors
// 3.3V max when defined as an analog input
//
#define TEMP_0_PIN                      P0_23_A0  // (T1)
#define TEMP_BED_PIN                    P0_24_A1  // (T2)
#define TEMP_1_PIN                      P0_25_A2  // (T3)
#define TEMP_2_PIN                      P0_26_A3  // (T4)

//
// Heaters / Fans
//
#define HEATER_BED_PIN                     P2_05
#define HEATER_0_PIN                       P2_07
#define HEATER_1_PIN                       P1_23
#ifndef FAN_PIN
  #define FAN_PIN                          P2_06
#endif
#define FAN1_PIN                           P2_04

//
// LCD / Controller
//
#if ANY(VIKI2, miniVIKI)

  #define BEEPER_PIN                       P1_31
  #define DOGLCD_A0                        P2_11
  #define DOGLCD_CS                        P0_16

  #define BTN_EN1                          P3_25
  #define BTN_EN2                          P3_26
  #define BTN_ENC                          P1_30

  #define SD_DETECT_PIN                    P1_18
  #define SDSS                             P1_21

  #define STAT_LED_RED_PIN                 P1_19
  #define STAT_LED_BLUE_PIN                P1_20

#elif HAS_SPI_LCD

  #error "Marlin's Smoothieboard support cannot drive your LCD."

#endif